Category: I/O systems > X20 System > Analog inputs
2 analog inputs Either current or voltage signal possible 16-bit digital converter resolution Simultaneous input conversion Very fast conversion time The module is equipped with 2 inputs with 16-bit digital converter resolution.
It is possible to select between the current and voltage signal using different terminals.
This module is designed for X20 6-pin terminal blocks. If needed (e.g.
for logistical reasons), the 12-pin terminal block can also be used.
Technical Specifications
Short description
- I/O module = 2 analog inputs ±10 V or 0 to 20 mA
General information
- Diagnostics
- Module run/error = Yes, using LED status indicator and software
- Inputs = Yes, using LED status indicator and software
- Channel type = Yes, using software
- Power consumption
- Bus = 0.01 W
- Internal I/O = 1.2 W
- Certifications
- CE = Yes
- UKCA = Yes
- CRA (Cyber Resilience Act) = In preparation
- ATEX = Zone 2, II 3G Ex nA nC IIA T5 Gc IP20, Ta (see X20 user's manual) FTZÚ 09 ATEX 0083X
- UL = cULus E115267 Industrial control equipment
- HazLoc = cCSAus 244665 Process control equipment for hazardous locations Class I, Division 2, Groups ABCD, T5
- DNV = Temperature: B (0 to 55°C) Humidity: B (up to 100%) Vibration: B (4 g) EMC: B (bridge and open deck)
- CCS = Yes
- LR = ENV1
- KR = Yes
- ABS = Yes
- BV = EC33B Temperature: 5 - 55°C Vibration: 4 g EMC: Bridge and open deck
- KC = Yes
- B&R ID code = 0x1BA0
- Status indicators = I/O function per channel, operating state, module status
- Additional power dissipation caused by actuators (resistive) [W] = -
Analog inputs
- Digital converter resolution
- Voltage = ±15-bit
- Current = 15-bit
- Output format
- Voltage = INT 0x8001 - 0x7FFF / 1 LSB = 0x0001 = 305.176 µV
- Current = INT 0x0000 - 0x7FFF / 1 LSB = 0x0001 = 610.352 nA
- Input impedance in signal range
- Voltage = 20 MΩ
- Current = -
- Load
- Voltage = -
- Current = <400 Ω
- Permissible input signal
- Voltage = Max. ±30 V
- Current = Max. ±50 mA
- Output of digital value during overload
- Undershoot
- Voltage = 0x8001
- Current = 0x0000
- Overshoot
- Voltage = 0x7FFF
- Current = 0x7FFF
- Max. error
- Voltage
- Gain = 0.08%
- Offset = 0.01%
- Current
- Offset = 0.02%
- Max. gain drift
- Voltage = 0.01%/°C
- Current = 0.01%/°C
- Max. offset drift
- Voltage = 0.001%/°C
- Current = 0.002%/°C
- Common-mode rejection
- DC = 70 dB
- 50 Hz = 70 dB
- Nonlinearity
- Voltage = <0.01%
- Current = <0.015%
- Input = ±10 V or 0 to 20 mA, via different terminal connections
- Input type = Differential input
- Conversion time = 50 μs for all inputs
- Output format = INT
- Input protection = Protection against wiring with supply voltage
- Conversion procedure = SAR
- Input filter = Hardware - Third-order low-pass filter / cutoff frequency 10 kHz
- Common-mode range = ±12 V
- Crosstalk between channels = <-70 dB
- Insulation voltage between channel and bus = 500 V eff
Electrical properties
- Electrical isolation = Channel isolated from bus Channel not isolated from channel
Operating conditions
- Mounting orientation
- Horizontal = Yes
- Vertical = Yes
- Installation elevation above sea level
- 0 to 2000 m = No limitation
- >2000 m = Reduction of ambient temperature by 0.5°C per 100 m
- Degree of protection per EN 60529 = IP20
Ambient conditions
- Temperature
- Operation
- Horizontal mounting orientation = -25 to 60°C
- Vertical mounting orientation = -25 to 50°C
- Derating = -
- Storage = -40 to 85°C
- Transport = -40 to 85°C
- Relative humidity
- Operation = 5 to 95%, non-condensing
- Storage = 5 to 95%, non-condensing
- Transport = 5 to 95%, non-condensing
Mechanical properties
- Note = Order 1x terminal block X20TB06 or X20TB12 separately. Order 1x bus module X20BM11 separately.
- Pitch = 12.5 +0.2 mm
